Free safety-glass stamp decoder
What does the stamp on my glass mean?
Type the stamp from the corner of the glass, line by line. GlassRef explains every mark: tempered or laminated, the safety category, the standard, the maker and the date. It reads the mark; it never tests or certifies glass.
Point your iPhone at the stamp instead
The free GlassRef app reads the stamp with the camera and saves it to a project. A GlassRef account also looks up every maker’s glass and builds and compares makeups.
How to read a safety-glass stamp
Safety glass in doors, shower and tub enclosures, and other hazardous locations usually carries a small permanent mark (the “bug”) in one corner: sandblasted, acid-etched or fired into the surface. It is easiest to read with light at a low angle. Here is what each part means.
Tempered (toughened), heat-soaked, laminated, heat-strengthened, wired
Fully tempered glass was heated and quenched so that it breaks into small, blunt pieces; it can’t be cut, drilled or edged afterwards. Heat-soaked glass is tempered glass that was also heat-soak tested, to lower the risk of spontaneous breakage from nickel-sulfide inclusions (EN 14179 in Europe). Laminated glass is two or more lites bonded with an interlayer; when it breaks, the pieces stay stuck to the interlayer. Heat-strengthened glass is about twice as strong as ordinary annealed glass but breaks into large pieces, so on its own it is not safety glass. Wired glass has a wire mesh inside, mainly for fire-rated openings.
CPSC 16 CFR 1201, Category I or II
The US federal safety-glazing standard. Category II is the higher impact category, for doors and larger glazing in hazardous locations. Category I is the lower one, for smaller lites (generally up to 9 ft²). Read this one carefully: Category II is often etched as two thin bars, and a worn stamp can look like a single “I”.
ANSI Z97.1 and a year
The US voluntary safety-glazing standard for glass in buildings (impact and how it breaks). The year after it is the edition, for example ANSI Z97.1-2015.
SGCC and a number
Certified by the Safety Glazing Certification Council. The number identifies the certified fabricator and plant, which is how you can trace who made the lite.
IGCC and a number
Printed on insulating glass units (often on the spacer), not on the glass: the unit was certified by the Insulating Glass Certification Council, and the number identifies the unit maker.
ASTM C1048, Kind FT or Kind HS
The US standard for heat-treated flat glass. Kind FT means fully tempered; Kind HS means heat-strengthened.
Miami-Dade (MDCA) and an approval number
Marked for a Miami-Dade County product approval (NOA): hurricane-zone impact glazing. The window’s NOA document says what the approval covers.
Canada, Europe, Australia and New Zealand
CAN/CGSB-12.1 is the Canadian safety-glazing standard (with a type and class). EN 12150 is European tempered (toughened) safety glass, EN 14179 heat-soaked tempered glass, EN 14449 laminated glass, and EN 12600 the pendulum impact test, whose class reads as impact level, breakage mode and drop height (for example 1(C)1). AS/NZS 2208 is the Australian and New Zealand standard; Grade A means tempered or laminated safety glass.
Date code, thickness and maker
Many stamps carry a month and year (05-19 or MAY 2019), the glass thickness (1/4" or 6 mm) and the fabricator’s name or logo. Big makers are often recognizable by name; smaller fabricators are identified by their SGCC number.
When there is no stamp
A lite without a mark may have lost it when it was cut from a larger tempered sheet (tempered glass can’t be cut, so that points to annealed glass), or the mark may be on an edge hidden by the frame or a gasket. The decoder can only read what is marked. When safety matters, have a glazier check it.
Questions
How do I know if my glass is tempered?
Look in each corner for a small etched or fired stamp; a mark that says TEMPERED, 16 CFR 1201 or ANSI Z97.1 means the glass was marked as safety glass. Type it into the decoder above and GlassRef explains every part. No stamp is not proof either way: some lites lose the mark when they are cut down or re-glazed, so ask a glazier when it matters.
What is the difference between Category I and Category II?
Both are CPSC 16 CFR 1201 safety-glazing categories. Category II passes a higher-energy impact test and is the one required for doors and larger panels in hazardous locations; Category I covers smaller lites (generally up to 9 ft²).
Does GlassRef test or certify my glass?
No. GlassRef reads the mark and says what it means, as marked. It never tests or certifies glass. Lines it is unsure about are flagged so you can check them against the stamp.
Can I read a stamp with my phone camera?
Yes, in the free GlassRef iPhone app: point the camera at the stamp and it reads it by itself, then you can save it to a project. On the web, type it as above.
What does the SGCC number tell me?
It identifies the certified fabricator and plant that made the lite. GlassRef shows the fabricator’s name when GlassRef staff have confirmed which company the number belongs to.
Is heat-strengthened glass safety glass?
Not on its own. It is about twice as strong as annealed glass but breaks into large pieces. It can be part of a laminated safety glass, and a stamp that also shows 16 CFR 1201 or ANSI Z97.1 says the finished product was marked as safety glazing.
More free tools
GlassRef publishes reference data and shows where every number came from. It does not test, certify or approve products; product certification belongs to bodies such as NFRC and SGCC, and the design professional of record signs off on what goes into a building. GlassRef is independent and not affiliated with LBNL, NFRC, ENERGY STAR or any manufacturer.